/**
|
* Marvell BT-over-SDIO driver: SDIO interface related definitions
|
*
|
* Copyright (C) 2009, Marvell International Ltd.
|
*
|
* This software file (the "File") is distributed by Marvell International
|
* Ltd. under the terms of the GNU General Public License Version 2, June 1991
|
* (the "License"). You may use, redistribute and/or modify this File in
|
* accordance with the terms and conditions of the License, a copy of which
|
* is available by writing to the Free Software Foundation, Inc.,
|
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA or on the
|
* worldwide web at http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
|
*
|
*
|
* THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
|
* IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
|
* ARE EXPRESSLY DISCLAIMED. The License provides additional details about
|
* this warranty disclaimer.
|
*
|
**/
|
|
#define SDIO_HEADER_LEN 4
|
|
/* SD block size can not bigger than 64 due to buf size limit in firmware */
|
/* define SD block size for data Tx/Rx */
|
#define SDIO_BLOCK_SIZE 64
|
|
/* Number of blocks for firmware transfer */
|
#define FIRMWARE_TRANSFER_NBLOCK 2
|
|
/* This is for firmware specific length */
|
#define FW_EXTRA_LEN 36
|
|
#define MRVDRV_SIZE_OF_CMD_BUFFER (2 * 1024)
|
|
#define MRVDRV_BT_RX_PACKET_BUFFER_SIZE \
|
(HCI_MAX_FRAME_SIZE + FW_EXTRA_LEN)
|
|
#define ALLOC_BUF_SIZE (((max_t (int, MRVDRV_BT_RX_PACKET_BUFFER_SIZE, \
|
MRVDRV_SIZE_OF_CMD_BUFFER) + SDIO_HEADER_LEN \
|
+ SDIO_BLOCK_SIZE - 1) / SDIO_BLOCK_SIZE) \
|
* SDIO_BLOCK_SIZE)
|
|
/* The number of times to try when polling for status */
|
#define MAX_POLL_TRIES 100
|
|
/* Max retry number of CMD53 write */
|
#define MAX_WRITE_IOMEM_RETRY 2
|
|
/* register bitmasks */
|
#define HOST_POWER_UP BIT(1)
|
#define HOST_CMD53_FIN BIT(2)
|
|
#define HIM_DISABLE 0xff
|
#define HIM_ENABLE (BIT(0) | BIT(1))
|
|
#define UP_LD_HOST_INT_STATUS BIT(0)
|
#define DN_LD_HOST_INT_STATUS BIT(1)
|
|
#define DN_LD_CARD_RDY BIT(0)
|
#define CARD_IO_READY BIT(3)
|
|
#define FIRMWARE_READY 0xfedc
|
|
struct btmrvl_plt_wake_cfg {
|
int irq_bt;
|
bool wake_by_bt;
|
};
|
|
struct btmrvl_sdio_card_reg {
|
u8 cfg;
|
u8 host_int_mask;
|
u8 host_intstatus;
|
u8 card_status;
|
u8 sq_read_base_addr_a0;
|
u8 sq_read_base_addr_a1;
|
u8 card_revision;
|
u8 card_fw_status0;
|
u8 card_fw_status1;
|
u8 card_rx_len;
|
u8 card_rx_unit;
|
u8 io_port_0;
|
u8 io_port_1;
|
u8 io_port_2;
|
bool int_read_to_clear;
|
u8 host_int_rsr;
|
u8 card_misc_cfg;
|
u8 fw_dump_ctrl;
|
u8 fw_dump_start;
|
u8 fw_dump_end;
|
};
|
|
struct btmrvl_sdio_card {
|
struct sdio_func *func;
|
u32 ioport;
|
const char *helper;
|
const char *firmware;
|
const struct btmrvl_sdio_card_reg *reg;
|
bool support_pscan_win_report;
|
bool supports_fw_dump;
|
u16 sd_blksz_fw_dl;
|
u8 rx_unit;
|
struct btmrvl_private *priv;
|
struct device_node *plt_of_node;
|
struct btmrvl_plt_wake_cfg *plt_wake_cfg;
|
};
|
|
struct btmrvl_sdio_device {
|
const char *helper;
|
const char *firmware;
|
const struct btmrvl_sdio_card_reg *reg;
|
const bool support_pscan_win_report;
|
u16 sd_blksz_fw_dl;
|
bool supports_fw_dump;
|
};
|
|
|
/* Platform specific DMA alignment */
|
#define BTSDIO_DMA_ALIGN 8
|
|
/* Macros for Data Alignment : size */
|
#define ALIGN_SZ(p, a) \
|
(((p) + ((a) - 1)) & ~((a) - 1))
|
|
/* Macros for Data Alignment : address */
|
#define ALIGN_ADDR(p, a) \
|
((((unsigned long)(p)) + (((unsigned long)(a)) - 1)) & \
|
~(((unsigned long)(a)) - 1))
|
