// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
// Copyright (C) 2017 Antony Antony <antony@phenome.org>
|
// Copyright (C) 2016 ARM Ltd.
|
|
/dts-v1/;
|
#include "sun50i-h5.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
#include <dt-bindings/input/input.h>
|
#include <dt-bindings/pinctrl/sun4i-a10.h>
|
|
/ {
|
model = "FriendlyARM NanoPi NEO Plus2";
|
compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
|
|
aliases {
|
ethernet0 = &emac;
|
serial0 = &uart0;
|
};
|
|
chosen {
|
stdout-path = "serial0:115200n8";
|
};
|
|
leds {
|
compatible = "gpio-leds";
|
|
pwr {
|
label = "nanopi:green:pwr";
|
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
|
default-state = "on";
|
};
|
|
status {
|
label = "nanopi:red:status";
|
gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
|
};
|
};
|
|
reg_gmac_3v3: gmac-3v3 {
|
compatible = "regulator-fixed";
|
regulator-name = "gmac-3v3";
|
regulator-min-microvolt = <3300000>;
|
regulator-max-microvolt = <3300000>;
|
startup-delay-us = <100000>;
|
enable-active-high;
|
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
|
};
|
|
reg_vcc3v3: vcc3v3 {
|
compatible = "regulator-fixed";
|
regulator-name = "vcc3v3";
|
regulator-min-microvolt = <3300000>;
|
regulator-max-microvolt = <3300000>;
|
};
|
|
vdd_cpux: gpio-regulator {
|
compatible = "regulator-gpio";
|
regulator-name = "vdd-cpux";
|
regulator-type = "voltage";
|
regulator-boot-on;
|
regulator-always-on;
|
regulator-min-microvolt = <1100000>;
|
regulator-max-microvolt = <1300000>;
|
regulator-ramp-delay = <50>; /* 4ms */
|
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
|
gpios-states = <0x1>;
|
states = <1100000 0>, <1300000 1>;
|
};
|
|
wifi_pwrseq: wifi_pwrseq {
|
compatible = "mmc-pwrseq-simple";
|
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
post-power-on-delay-ms = <200>;
|
};
|
};
|
|
&codec {
|
allwinner,audio-routing =
|
"Line Out", "LINEOUT",
|
"MIC1", "Mic",
|
"Mic", "MBIAS";
|
status = "okay";
|
};
|
|
&ehci0 {
|
status = "okay";
|
};
|
|
&ehci3 {
|
status = "okay";
|
};
|
|
&emac {
|
pinctrl-names = "default";
|
pinctrl-0 = <&emac_rgmii_pins>;
|
phy-supply = <®_gmac_3v3>;
|
phy-handle = <&ext_rgmii_phy>;
|
phy-mode = "rgmii-id";
|
status = "okay";
|
};
|
|
&external_mdio {
|
ext_rgmii_phy: ethernet-phy@7 {
|
compatible = "ethernet-phy-ieee802.3-c22";
|
reg = <7>;
|
};
|
};
|
|
&mmc0 {
|
vmmc-supply = <®_vcc3v3>;
|
bus-width = <4>;
|
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
|
status = "okay";
|
};
|
|
&mmc1 {
|
vmmc-supply = <®_vcc3v3>;
|
vqmmc-supply = <®_vcc3v3>;
|
mmc-pwrseq = <&wifi_pwrseq>;
|
bus-width = <4>;
|
non-removable;
|
status = "okay";
|
|
brcmf: wifi@1 {
|
reg = <1>;
|
compatible = "brcm,bcm4329-fmac";
|
};
|
};
|
|
&mmc2 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&mmc2_8bit_pins>;
|
vmmc-supply = <®_vcc3v3>;
|
bus-width = <8>;
|
non-removable;
|
cap-mmc-hw-reset;
|
status = "okay";
|
};
|
|
&ohci0 {
|
status = "okay";
|
};
|
|
&ohci3 {
|
status = "okay";
|
};
|
|
&uart0 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&uart0_pa_pins>;
|
status = "okay";
|
};
|
|
&usb_otg {
|
dr_mode = "host";
|
status = "okay";
|
};
|
|
&usbphy {
|
/* USB Type-A ports' VBUS is always on */
|
status = "okay";
|
};
|
