/*
|
* (C) Copyright 2014
|
* Vikas Manocha, ST Micoelectronics, vikas.manocha@st.com.
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#include <common.h>
|
#include <dm.h>
|
#include <miiphy.h>
|
#include <asm/arch/stv0991_periph.h>
|
#include <asm/arch/stv0991_defs.h>
|
#include <asm/arch/hardware.h>
|
#include <asm/arch/gpio.h>
|
#include <netdev.h>
|
#include <asm/io.h>
|
#include <dm/platform_data/serial_pl01x.h>
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
struct gpio_regs *const gpioa_regs =
|
(struct gpio_regs *) GPIOA_BASE_ADDR;
|
|
#ifndef CONFIG_OF_CONTROL
|
static const struct pl01x_serial_platdata serial_platdata = {
|
.base = 0x80406000,
|
.type = TYPE_PL011,
|
.clock = 2700 * 1000,
|
};
|
|
U_BOOT_DEVICE(stv09911_serials) = {
|
.name = "serial_pl01x",
|
.platdata = &serial_platdata,
|
};
|
#endif
|
|
#ifdef CONFIG_SHOW_BOOT_PROGRESS
|
void show_boot_progress(int progress)
|
{
|
printf("%i\n", progress);
|
}
|
#endif
|
|
void enable_eth_phy(void)
|
{
|
/* Set GPIOA_06 pad HIGH (Appli board)*/
|
writel(readl(&gpioa_regs->dir) | 0x40, &gpioa_regs->dir);
|
writel(readl(&gpioa_regs->data) | 0x40, &gpioa_regs->data);
|
}
|
int board_eth_enable(void)
|
{
|
stv0991_pinmux_config(ETH_GPIOB_10_31_C_0_4);
|
clock_setup(ETH_CLOCK_CFG);
|
enable_eth_phy();
|
return 0;
|
}
|
|
int board_qspi_enable(void)
|
{
|
stv0991_pinmux_config(QSPI_CS_CLK_PAD);
|
clock_setup(QSPI_CLOCK_CFG);
|
return 0;
|
}
|
|
/*
|
* Miscellaneous platform dependent initialisations
|
*/
|
int board_init(void)
|
{
|
board_eth_enable();
|
board_qspi_enable();
|
return 0;
|
}
|
|
int board_uart_init(void)
|
{
|
stv0991_pinmux_config(UART_GPIOC_30_31);
|
clock_setup(UART_CLOCK_CFG);
|
return 0;
|
}
|
|
#ifdef CONFIG_BOARD_EARLY_INIT_F
|
int board_early_init_f(void)
|
{
|
board_uart_init();
|
return 0;
|
}
|
#endif
|
|
int dram_init(void)
|
{
|
gd->ram_size = PHYS_SDRAM_1_SIZE;
|
return 0;
|
}
|
|
int dram_init_banksize(void)
|
{
|
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
|
gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
|
|
return 0;
|
}
|
|
#ifdef CONFIG_CMD_NET
|
int board_eth_init(bd_t *bis)
|
{
|
int ret = 0;
|
|
#if defined(CONFIG_ETH_DESIGNWARE)
|
u32 interface = PHY_INTERFACE_MODE_MII;
|
if (designware_initialize(GMAC_BASE_ADDR, interface) >= 0)
|
ret++;
|
#endif
|
return ret;
|
}
|
#endif
|
