# SPDX-License-Identifier: GPL-2.0
|
#
|
# Physical Layer USB driver configuration
|
#
|
menu "USB Physical Layer drivers"
|
|
config USB_PHY
|
select EXTCON
|
def_bool n
|
|
#
|
# USB Transceiver Drivers
|
#
|
config AB8500_USB
|
tristate "AB8500 USB Transceiver Driver"
|
depends on AB8500_CORE
|
select USB_PHY
|
help
|
Enable this to support the USB OTG transceiver in AB8500 chip.
|
This transceiver supports high and full speed devices plus,
|
in host mode, low speed.
|
|
config FSL_USB2_OTG
|
tristate "Freescale USB OTG Transceiver Driver"
|
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
|
select USB_PHY
|
help
|
Enable this to support Freescale USB OTG transceiver.
|
|
config ISP1301_OMAP
|
tristate "Philips ISP1301 with OMAP OTG"
|
depends on I2C && ARCH_OMAP_OTG
|
depends on USB
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
|
select USB_PHY
|
help
|
If you say yes here you get support for the Philips ISP1301
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
The ISP1301 is a full speed USB transceiver which is used in
|
products including H2, H3, and H4 development boards for Texas
|
Instruments OMAP processors.
|
|
This driver can also be built as a module. If so, the module
|
will be called phy-isp1301-omap.
|
|
config KEYSTONE_USB_PHY
|
tristate "Keystone USB PHY Driver"
|
depends on ARCH_KEYSTONE || COMPILE_TEST
|
depends on NOP_USB_XCEIV
|
help
|
Enable this to support Keystone USB phy. This driver provides
|
interface to interact with USB 2.0 and USB 3.0 PHY that is part
|
of the Keystone SOC.
|
|
config NOP_USB_XCEIV
|
tristate "NOP USB Transceiver Driver"
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
|
select USB_PHY
|
help
|
This driver is to be used by all the usb transceiver which are either
|
built-in with usb ip or which are autonomous and doesn't require any
|
phy programming such as ISP1x04 etc.
|
|
config AM335X_CONTROL_USB
|
tristate
|
|
config AM335X_PHY_USB
|
tristate "AM335x USB PHY Driver"
|
depends on ARM || COMPILE_TEST
|
depends on NOP_USB_XCEIV
|
select USB_PHY
|
select AM335X_CONTROL_USB
|
select USB_COMMON
|
help
|
This driver provides PHY support for that phy which part for the
|
AM335x SoC.
|
|
config TWL6030_USB
|
tristate "TWL6030 USB Transceiver Driver"
|
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
|
depends on OF
|
help
|
Enable this to support the USB OTG transceiver on TWL6030
|
family chips. This TWL6030 transceiver has the VBUS and ID GND
|
and OTG SRP events capabilities. For all other transceiver functionality
|
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
|
are hooked to this driver through platform_data structure.
|
The definition of internal PHY APIs are in the mach-omap2 layer.
|
|
config USB_GPIO_VBUS
|
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
depends on GPIOLIB || COMPILE_TEST
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
|
select USB_PHY
|
help
|
Provides simple GPIO VBUS sensing for controllers with an
|
internal transceiver via the usb_phy interface, and
|
optionally control of a D+ pullup GPIO as well as a VBUS
|
current limit regulator.
|
|
config OMAP_OTG
|
tristate "OMAP USB OTG controller driver"
|
depends on ARCH_OMAP_OTG && EXTCON
|
help
|
Enable this to support some transceivers on OMAP1 platforms. OTG
|
controller is needed to switch between host and peripheral modes.
|
|
This driver can also be built as a module. If so, the module
|
will be called phy-omap-otg.
|
|
config TAHVO_USB
|
tristate "Tahvo USB transceiver driver"
|
depends on MFD_RETU
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
|
select USB_PHY
|
help
|
Enable this to support USB transceiver on Tahvo. This is used
|
at least on Nokia 770.
|
|
config TAHVO_USB_HOST_BY_DEFAULT
|
depends on TAHVO_USB
|
bool "Device in USB host mode by default"
|
help
|
Say Y here, if you want the device to enter USB host mode
|
by default on bootup.
|
|
config USB_ISP1301
|
tristate "NXP ISP1301 USB transceiver support"
|
depends on USB || USB_GADGET
|
depends on I2C
|
select USB_PHY
|
help
|
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
|
This chip is typically used as USB transceiver for USB host, gadget
|
and OTG drivers (to be selected separately).
|
|
To compile this driver as a module, choose M here: the
|
module will be called phy-isp1301.
|
|
config USB_MV_OTG
|
tristate "Marvell USB OTG support"
|
depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
|
select USB_PHY
|
help
|
Say Y here if you want to build Marvell USB OTG transciever
|
driver in kernel (including PXA and MMP series). This driver
|
implements role switch between EHCI host driver and gadget driver.
|
|
To compile this driver as a module, choose M here.
|
|
config USB_MXS_PHY
|
tristate "Freescale MXS USB PHY support"
|
depends on ARCH_MXC || ARCH_MXS
|
select STMP_DEVICE
|
select USB_PHY
|
help
|
Enable this to support the Freescale MXS USB PHY.
|
|
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
|
|
config USB_TEGRA_PHY
|
tristate "NVIDIA Tegra USB PHY Driver"
|
depends on ARCH_TEGRA || COMPILE_TEST
|
select USB_COMMON
|
select USB_PHY
|
select USB_ULPI
|
help
|
This driver provides PHY support for the USB controllers found
|
on NVIDIA Tegra SoC's.
|
|
config USB_ULPI
|
bool "Generic ULPI Transceiver Driver"
|
depends on ARM || ARM64 || COMPILE_TEST
|
select USB_ULPI_VIEWPORT
|
help
|
Enable this to support ULPI connected USB OTG transceivers which
|
are likely found on embedded boards.
|
|
config USB_ULPI_VIEWPORT
|
bool
|
help
|
Provides read/write operations to the ULPI phy register set for
|
controllers with a viewport register (e.g. Chipidea/ARC controllers).
|
|
config JZ4770_PHY
|
tristate "Ingenic SoCs Transceiver Driver"
|
depends on MIPS || COMPILE_TEST
|
select USB_PHY
|
help
|
This driver provides PHY support for the USB controller found
|
on the JZ-series and X-series SoCs from Ingenic.
|
|
endmenu
|
