// SPDX-License-Identifier: GPL-2.0
|
/*
|
* Support for CompuLab CM-T3730
|
*/
|
/dts-v1/;
|
|
#include "omap36xx.dtsi"
|
#include "omap3-cm-t3x30.dtsi"
|
|
/ {
|
model = "CompuLab CM-T3730";
|
compatible = "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap36xx", "ti,omap3";
|
|
wl12xx_vmmc2: wl12xx_vmmc2 {
|
compatible = "regulator-fixed";
|
regulator-name = "vw1271";
|
pinctrl-names = "default";
|
pinctrl-0 = <&wl12xx_gpio>;
|
regulator-min-microvolt = <1800000>;
|
regulator-max-microvolt = <1800000>;
|
gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>; /* gpio73 */
|
startup-delay-us = <20000>;
|
enable-active-high;
|
};
|
|
wl12xx_vaux2: wl12xx_vaux2 {
|
compatible = "regulator-fixed";
|
regulator-name = "vwl1271_vaux2";
|
regulator-min-microvolt = <1800000>;
|
regulator-max-microvolt = <1800000>;
|
vin-supply = <&vaux2>;
|
};
|
};
|
|
&omap3_pmx_wkup {
|
dss_dpi_pins_cm_t3730: pinmux_dss_dpi_pins_cm_t3730 {
|
pinctrl-single,pins = <
|
OMAP3_WKUP_IOPAD(0x2a08, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
|
OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
|
OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
|
OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
|
OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
|
OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
|
>;
|
};
|
};
|
|
&omap3_pmx_core {
|
|
mmc2_pins: pinmux_mmc2_pins {
|
pinctrl-single,pins = <
|
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
|
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
|
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
|
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
|
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
|
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
|
>;
|
};
|
|
wl12xx_gpio: pinmux_wl12xx_gpio {
|
pinctrl-single,pins = <
|
OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */
|
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */
|
>;
|
};
|
};
|
|
&mmc2 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&mmc2_pins>;
|
vmmc-supply = <&wl12xx_vmmc2>;
|
vqmmc-supply = <&wl12xx_vaux2>;
|
non-removable;
|
bus-width = <4>;
|
cap-power-off-card;
|
|
#address-cells = <1>;
|
#size-cells = <0>;
|
wlcore: wlcore@2 {
|
compatible = "ti,wl1271";
|
reg = <2>;
|
interrupt-parent = <&gpio5>;
|
interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */
|
ref-clock-frequency = <38400000>;
|
};
|
};
|
|
&dss {
|
status = "okay";
|
|
pinctrl-names = "default";
|
pinctrl-0 = <
|
&dss_dpi_pins_common
|
&dss_dpi_pins_cm_t3730
|
>;
|
};
|
