Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
|
|
This is a special case of a MDIO bus multiplexer. One or more GPIO
|
lines are used to control which child bus is connected.
|
|
Required properties in addition to the generic multiplexer properties:
|
|
- compatible : mdio-mux-gpio.
|
- gpios : GPIO specifiers for each GPIO line. One or more must be specified.
|
|
|
Example :
|
|
/* The parent MDIO bus. */
|
smi1: mdio@1180000001900 {
|
compatible = "cavium,octeon-3860-mdio";
|
#address-cells = <1>;
|
#size-cells = <0>;
|
reg = <0x11800 0x00001900 0x0 0x40>;
|
};
|
|
/*
|
An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
|
pair of GPIO lines. Child busses 2 and 3 populated with 4
|
PHYs each.
|
*/
|
mdio-mux {
|
compatible = "mdio-mux-gpio";
|
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
|
mdio-parent-bus = <&smi1>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
|
mdio@2 {
|
reg = <2>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
|
phy11: ethernet-phy@1 {
|
reg = <1>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <10 8>; /* Pin 10, active low */
|
};
|
phy12: ethernet-phy@2 {
|
reg = <2>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <10 8>; /* Pin 10, active low */
|
};
|
phy13: ethernet-phy@3 {
|
reg = <3>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <10 8>; /* Pin 10, active low */
|
};
|
phy14: ethernet-phy@4 {
|
reg = <4>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <10 8>; /* Pin 10, active low */
|
};
|
};
|
|
mdio@3 {
|
reg = <3>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
|
phy21: ethernet-phy@1 {
|
reg = <1>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <12 8>; /* Pin 12, active low */
|
};
|
phy22: ethernet-phy@2 {
|
reg = <2>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <12 8>; /* Pin 12, active low */
|
};
|
phy23: ethernet-phy@3 {
|
reg = <3>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <12 8>; /* Pin 12, active low */
|
};
|
phy24: ethernet-phy@4 {
|
reg = <4>;
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
<3 0x11 0 0x00aa>,
|
<3 0x12 0 0x4105>,
|
<3 0x13 0 0x0a60>;
|
interrupt-parent = <&gpio>;
|
interrupts = <12 8>; /* Pin 12, active low */
|
};
|
};
|
};
|
