/*
|
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
|
*
|
* Based on Kirkwood support:
|
* (C) Copyright 2009
|
* Marvell Semiconductor <www.marvell.com>
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#include <common.h>
|
#include <command.h>
|
#include <asm/mach-types.h>
|
#include <asm/arch/cpu.h>
|
#include <asm/arch/soc.h>
|
#include <asm/arch/mpp.h>
|
#include <asm/arch/gpio.h>
|
|
#include "netspace_v2.h"
|
#include "../common/common.h"
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
int board_early_init_f(void)
|
{
|
/* Gpio configuration */
|
mvebu_config_gpio(NETSPACE_V2_OE_VAL_LOW, NETSPACE_V2_OE_VAL_HIGH,
|
NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
|
|
/* Multi-Purpose Pins Functionality configuration */
|
static const u32 kwmpp_config[] = {
|
MPP0_SPI_SCn,
|
MPP1_SPI_MOSI,
|
MPP2_SPI_SCK,
|
MPP3_SPI_MISO,
|
MPP4_NF_IO6,
|
MPP5_NF_IO7,
|
MPP6_SYSRST_OUTn,
|
MPP7_GPO, /* Fan speed (bit 1) */
|
MPP8_TW_SDA,
|
MPP9_TW_SCK,
|
MPP10_UART0_TXD,
|
MPP11_UART0_RXD,
|
MPP12_GPO, /* Red led */
|
MPP14_GPIO, /* USB fuse */
|
MPP16_GPIO, /* SATA 0 power */
|
MPP17_GPIO, /* SATA 1 power */
|
MPP18_NF_IO0,
|
MPP19_NF_IO1,
|
MPP20_SATA1_ACTn,
|
MPP21_SATA0_ACTn,
|
MPP22_GPIO, /* Fan speed (bit 0) */
|
MPP23_GPIO, /* Fan power */
|
MPP24_GPIO, /* USB mode select */
|
MPP25_GPIO, /* Fan rotation fail */
|
MPP26_GPIO, /* USB vbus-in detection */
|
MPP28_GPIO, /* USB enable vbus-out */
|
MPP29_GPIO, /* Blue led (slow register) */
|
MPP30_GPIO, /* Blue led (command register) */
|
MPP31_GPIO, /* Board power off */
|
MPP32_GPIO, /* Button (0 = Released, 1 = Pushed) */
|
MPP33_GPIO, /* Fan speed (bit 2) */
|
0
|
};
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
}
|
|
int board_init(void)
|
{
|
/* Machine number */
|
gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
|
|
/* Boot parameters address */
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
return 0;
|
}
|
|
#if defined(CONFIG_MISC_INIT_R)
|
int misc_init_r(void)
|
{
|
#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
|
if (!env_get("ethaddr")) {
|
uchar mac[6];
|
if (lacie_read_mac_address(mac) == 0)
|
eth_env_set_enetaddr("ethaddr", mac);
|
}
|
#endif
|
return 0;
|
}
|
#endif
|
|
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
|
/* Configure and initialize PHY */
|
void reset_phy(void)
|
{
|
#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
|
mv_phy_88e1318_init("egiga0", 0);
|
#else
|
mv_phy_88e1116_init("egiga0", 8);
|
#endif
|
}
|
#endif
|
|
#if defined(CONFIG_KIRKWOOD_GPIO)
|
/* Return GPIO button status */
|
static int
|
do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
{
|
return kw_gpio_get_value(NETSPACE_V2_GPIO_BUTTON);
|
}
|
|
U_BOOT_CMD(button, 1, 1, do_read_button,
|
"Return GPIO button status 0=off 1=on", "");
|
#endif
|
