#ifndef __UBOOT_SL811_H
|
#define __UBOOT_SL811_H
|
|
#undef SL811_DEBUG
|
|
#ifdef SL811_DEBUG
|
#define PDEBUG(level, fmt, args...) \
|
if (debug >= (level)) printf("[%s:%d] " fmt, \
|
__PRETTY_FUNCTION__, __LINE__ , ## args)
|
#else
|
#define PDEBUG(level, fmt, args...) do {} while(0)
|
#endif
|
|
/* Sl811 host control register */
|
#define SL811_CTRL_A 0x00
|
#define SL811_ADDR_A 0x01
|
#define SL811_LEN_A 0x02
|
#define SL811_STS_A 0x03 /* read */
|
#define SL811_PIDEP_A 0x03 /* write */
|
#define SL811_CNT_A 0x04 /* read */
|
#define SL811_DEV_A 0x04 /* write */
|
#define SL811_CTRL1 0x05
|
#define SL811_INTR 0x06
|
#define SL811_CTRL_B 0x08
|
#define SL811_ADDR_B 0x09
|
#define SL811_LEN_B 0x0A
|
#define SL811_STS_B 0x0B /* read */
|
#define SL811_PIDEP_B 0x0B /* write */
|
#define SL811_CNT_B 0x0C /* read */
|
#define SL811_DEV_B 0x0C /* write */
|
#define SL811_INTRSTS 0x0D /* write clears bitwise */
|
#define SL811_HWREV 0x0E /* read */
|
#define SL811_SOFLOW 0x0E /* write */
|
#define SL811_SOFCNTDIV 0x0F /* read */
|
#define SL811_CTRL2 0x0F /* write */
|
|
/* USB control register bits (addr 0x00 and addr 0x08) */
|
#define SL811_USB_CTRL_ARM 0x01
|
#define SL811_USB_CTRL_ENABLE 0x02
|
#define SL811_USB_CTRL_DIR_OUT 0x04
|
#define SL811_USB_CTRL_ISO 0x10
|
#define SL811_USB_CTRL_SOF 0x20
|
#define SL811_USB_CTRL_TOGGLE_1 0x40
|
#define SL811_USB_CTRL_PREAMBLE 0x80
|
|
/* USB status register bits (addr 0x03 and addr 0x0B) */
|
#define SL811_USB_STS_ACK 0x01
|
#define SL811_USB_STS_ERROR 0x02
|
#define SL811_USB_STS_TIMEOUT 0x04
|
#define SL811_USB_STS_TOGGLE_1 0x08
|
#define SL811_USB_STS_SETUP 0x10
|
#define SL811_USB_STS_OVERFLOW 0x20
|
#define SL811_USB_STS_NAK 0x40
|
#define SL811_USB_STS_STALL 0x80
|
|
/* Control register 1 bits (addr 0x05) */
|
#define SL811_CTRL1_SOF 0x01
|
#define SL811_CTRL1_RESET 0x08
|
#define SL811_CTRL1_JKSTATE 0x10
|
#define SL811_CTRL1_SPEED_LOW 0x20
|
#define SL811_CTRL1_SUSPEND 0x40
|
|
/* Interrut enable (addr 0x06) and interrupt status register bits (addr 0x0D) */
|
#define SL811_INTR_DONE_A 0x01
|
#define SL811_INTR_DONE_B 0x02
|
#define SL811_INTR_SOF 0x10
|
#define SL811_INTR_INSRMV 0x20
|
#define SL811_INTR_DETECT 0x40
|
#define SL811_INTR_NOTPRESENT 0x40
|
#define SL811_INTR_SPEED_FULL 0x80 /* only in status reg */
|
|
/* HW rev and SOF lo register bits (addr 0x0E) */
|
#define SL811_HWR_HWREV 0xF0
|
|
/* SOF counter and control reg 2 (addr 0x0F) */
|
#define SL811_CTL2_SOFHI 0x3F
|
#define SL811_CTL2_DSWAP 0x40
|
#define SL811_CTL2_HOST 0x80
|
|
/* Set up for 1-ms SOF time. */
|
#define SL811_12M_LOW 0xE0
|
#define SL811_12M_HI 0x2E
|
|
#define SL811_DATA_START 0x10
|
#define SL811_DATA_LIMIT 240
|
|
/* Requests: bRequest << 8 | bmRequestType */
|
#define RH_GET_STATUS 0x0080
|
#define RH_CLEAR_FEATURE 0x0100
|
#define RH_SET_FEATURE 0x0300
|
#define RH_SET_ADDRESS 0x0500
|
#define RH_GET_DESCRIPTOR 0x0680
|
#define RH_SET_DESCRIPTOR 0x0700
|
#define RH_GET_CONFIGURATION 0x0880
|
#define RH_SET_CONFIGURATION 0x0900
|
#define RH_GET_STATE 0x0280
|
#define RH_GET_INTERFACE 0x0A80
|
#define RH_SET_INTERFACE 0x0B00
|
#define RH_SYNC_FRAME 0x0C80
|
|
|
#define PIDEP(pid, ep) (((pid) & 0x0f) << 4 | (ep))
|
|
#endif /* __UBOOT_SL811_H */
|
