// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
/*
|
* Copyright (c) 2023 Rockchip Electronics Co., Ltd.
|
*
|
*/
|
|
/dts-v1/;
|
|
#include <dt-bindings/gpio/gpio.h>
|
#include <dt-bindings/pinctrl/rockchip.h>
|
#include <dt-bindings/mfd/rockchip-serdes.h>
|
#include "rk3568.dtsi"
|
#include "rk3568-evb.dtsi"
|
|
/ {
|
model = "Rockchip RK3568M SERDES EVB LP4X V10 Board";
|
compatible = "rockchip,rk3568m-serdes-evb-lp4x-v10", "rockchip,rk3568";
|
|
vcc2v5_sys: vcc2v5-ddr {
|
compatible = "regulator-fixed";
|
regulator-name = "vcc2v5-sys";
|
regulator-always-on;
|
regulator-boot-on;
|
regulator-min-microvolt = <2500000>;
|
regulator-max-microvolt = <2500000>;
|
vin-supply = <&vcc3v3_sys>;
|
};
|
|
vcc3v3_bu: vcc3v3-bu {
|
compatible = "regulator-fixed";
|
regulator-name = "vcc3v3_bu";
|
regulator-always-on;
|
regulator-boot-on;
|
regulator-min-microvolt = <3300000>;
|
regulator-max-microvolt = <3300000>;
|
vin-supply = <&vcc5v0_sys>;
|
};
|
};
|
|
/*
|
* pin conflict with i2c2 for serdes-debug
|
*/
|
>1x {
|
status = "disabled";
|
};
|
|
&combphy0_us {
|
status = "okay";
|
};
|
|
&combphy2_psq {
|
status = "okay";
|
};
|
|
&i2c0 {
|
status = "okay";
|
|
gs_mxc6655xa: gs_mxc6655xa@15 {
|
status = "okay";
|
compatible = "gs_mxc6655xa";
|
pinctrl-names = "default";
|
pinctrl-0 = <&mxc6655xa_irq_gpio>;
|
reg = <0x15>;
|
irq-gpio = <&gpio0 RK_PA4 IRQ_TYPE_LEVEL_LOW>;
|
irq_enable = <0>;
|
poll_delay_ms = <30>;
|
type = <SENSOR_TYPE_ACCEL>;
|
power-off-in-suspend = <1>;
|
layout = <1>;
|
};
|
};
|
|
&i2c3 {
|
status = "okay";
|
clock-frequency = <100000>;
|
|
rkx120_x110: rkx120_x110@54 {
|
compatible = "rockchip,rkx120";
|
reg = <0x54>;
|
remote0-addr = <0x55>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
status = "okay";
|
|
serdes_camera: serdes-camera {
|
compatible = "rockchip,serdes-camera";
|
reg = <0>;
|
status = "okay";
|
};
|
};
|
};
|
|
&i2c5 {
|
status = "disabled";
|
};
|
|
&pinctrl {
|
mxc6655xa {
|
mxc6655xa_irq_gpio: mxc6655xa_irq_gpio {
|
rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
|
};
|
};
|
|
serdes {
|
rkx120_reset_gpio: rkx120-reset-gpio {
|
rockchip,pins = <2 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
|
};
|
};
|
};
|
|
&pmu_io_domains {
|
vccio6-supply = <&vcc_3v3>;
|
};
|
|
&pwm7 {
|
status = "disabled";
|
};
|
|
&rk809_codec {
|
status = "disabled";
|
};
|
|
&sdmmc0 {
|
status = "disabled";
|
};
|
|
&sdmmc2 {
|
status = "disabled";
|
};
|
|
&uart1 {
|
status = "okay";
|
pinctrl-names = "default";
|
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
|
};
|
|
&wireless_wlan {
|
status = "disabled";
|
};
|
|
&wireless_bluetooth {
|
status = "disabled";
|
};
|
|
/* OTG0 */
|
&combphy0_us {
|
rockchip,dis-u3otg0-port;
|
/* OTG and SATA0 not use combphy0_us, then disabled */
|
status = "disabled";
|
};
|
|
&u2phy0_otg {
|
vbus-supply = <&vcc5v0_otg>;
|
status = "okay";
|
};
|
|
&usb2phy0 {
|
status = "okay";
|
};
|
|
&usbdrd_dwc3 {
|
dr_mode = "otg";
|
phys = <&u2phy0_otg>;
|
phy-names = "usb2-phy";
|
extcon = <&usb2phy0>;
|
maximum-speed = "high-speed";
|
snps,dis_u2_susphy_quirk;
|
status = "okay";
|
};
|
|
&usbdrd30 {
|
status = "okay";
|
};
|
|
/* HOST1 */
|
&combphy1_usq {
|
status = "okay";
|
};
|
|
&u2phy0_host {
|
phy-supply = <&vcc5v0_host>;
|
status = "okay";
|
};
|
|
&usb2phy0 {
|
status = "okay";
|
};
|
|
&usbhost_dwc3 {
|
status = "okay";
|
};
|
|
&usbhost30 {
|
status = "okay";
|
};
|