// SPDX-License-Identifier: GPL-2.0
|
/*
|
* accel driver for iam20680
|
*
|
* Copyright (c) 2021 Rockchip Electronics Co., Ltd.
|
*
|
* Author: sxj <sxj@rock-chips.com>
|
*
|
*/
|
#include <linux/interrupt.h>
|
#include <linux/i2c.h>
|
#include <linux/slab.h>
|
#include <linux/irq.h>
|
#include <linux/miscdevice.h>
|
#include <linux/gpio.h>
|
#include <linux/uaccess.h>
|
#include <linux/atomic.h>
|
#include <linux/delay.h>
|
#include <linux/input.h>
|
#include <linux/workqueue.h>
|
#include <linux/freezer.h>
|
#include <linux/of_gpio.h>
|
#ifdef CONFIG_HAS_EARLYSUSPEND
|
#include <linux/earlysuspend.h>
|
#endif
|
#include <linux/sensor-dev.h>
|
#include <linux/iam20680.h>
|
|
static int iam20680_set_rate(struct i2c_client *client, int rate)
|
{
|
/* always use poll mode, no need to set rate */
|
return 0;
|
}
|
|
static int sensor_active(struct i2c_client *client, int enable, int rate)
|
{
|
struct sensor_private_data *sensor =
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
int result = 0;
|
int status = 0;
|
u8 pwrm1 = 0;
|
|
sensor->ops->ctrl_data = sensor_read_reg(client, sensor->ops->ctrl_reg);
|
pwrm1 = sensor_read_reg(client, IAM20680_PWR_MGMT_1);
|
|
if (!enable) {
|
status = BIT_ACCEL_STBY;
|
sensor->ops->ctrl_data |= status;
|
if ((sensor->ops->ctrl_data & BIT_GYRO_STBY) == BIT_GYRO_STBY)
|
pwrm1 |= IAM20680_PWRM1_SLEEP;
|
} else {
|
status = ~BIT_ACCEL_STBY;
|
sensor->ops->ctrl_data &= status;
|
pwrm1 &= ~IAM20680_PWRM1_SLEEP;
|
|
iam20680_set_rate(client, rate);
|
}
|
result = sensor_write_reg(client, sensor->ops->ctrl_reg, sensor->ops->ctrl_data);
|
if (result) {
|
dev_err(&client->dev, "%s:fail to set pwrm2\n", __func__);
|
return -1;
|
}
|
msleep(20);
|
|
result = sensor_write_reg(client, IAM20680_PWR_MGMT_1, pwrm1);
|
if (result) {
|
dev_err(&client->dev, "%s:fail to set pwrm1\n", __func__);
|
return -1;
|
}
|
msleep(50);
|
|
return result;
|
}
|
|
static int sensor_init(struct i2c_client *client)
|
{
|
int res = 0;
|
struct sensor_private_data *sensor =
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
res = sensor_write_reg(client, IAM20680_PWR_MGMT_1, 0x80);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_PWR_MGMT_1 error,res: %d!\n", res);
|
return res;
|
}
|
msleep(40);
|
|
res = sensor_write_reg(client, IAM20680_GYRO_CONFIG, 0x18);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_GYRO_CONFIG error,res: %d!\n", res);
|
return res;
|
}
|
msleep(10);
|
|
res = sensor_write_reg(client, IAM20680_ACCEL_CONFIG, 0x00);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_ACCEL_CONFIG error,res: %d!\n", res);
|
return res;
|
}
|
msleep(10);
|
|
res = sensor_write_reg(client, IAM20680_ACCEL_CONFIG2, 0x00);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_ACCEL_CONFIG2 error,res: %d!\n", res);
|
return res;
|
}
|
res = sensor_write_reg(client, IAM20680_PWR_MGMT_2, 0x3F);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_PWR_MGMT_2 error,res: %d!\n", res);
|
return res;
|
}
|
msleep(10);
|
res = sensor_write_reg(client, IAM20680_PWR_MGMT_1, 0x41);
|
if (res) {
|
dev_err(&client->dev, "set IAM20680_PWR_MGMT_1 error,res: %d!\n", res);
|
return res;
|
}
|
msleep(10);
|
|
res = sensor->ops->active(client, 0, sensor->pdata->poll_delay_ms);
|
if (res) {
|
dev_err(&client->dev, "%s:line=%d,error\n", __func__, __LINE__);
|
return res;
|
}
|
return res;
|
}
|
|
static int gsensor_report_value(struct i2c_client *client, struct sensor_axis *axis)
|
{
|
struct sensor_private_data *sensor =
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
if (sensor->status_cur == SENSOR_ON) {
|
/* Report acceleration sensor information */
|
input_report_abs(sensor->input_dev, ABS_X, axis->x);
|
input_report_abs(sensor->input_dev, ABS_Y, axis->y);
|
input_report_abs(sensor->input_dev, ABS_Z, axis->z);
|
input_sync(sensor->input_dev);
|
}
|
|
return 0;
|
}
|
|
static int sensor_report_value(struct i2c_client *client)
|
{
|
struct sensor_private_data *sensor =
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
struct sensor_platform_data *pdata = sensor->pdata;
|
int ret = 0;
|
short x, y, z;
|
struct sensor_axis axis;
|
u8 buffer[6] = {0};
|
|
if (sensor->ops->read_len < 6) {
|
dev_err(&client->dev, "%s: length is error, len=%d\n",
|
__func__, sensor->ops->read_len);
|
return -1;
|
}
|
|
memset(buffer, 0, 6);
|
|
/* Data bytes from hardware xL, xH, yL, yH, zL, zH */
|
do {
|
*buffer = sensor->ops->read_reg;
|
ret = sensor_rx_data(client, buffer, sensor->ops->read_len);
|
if (ret < 0)
|
return ret;
|
} while (0);
|
|
x = ((buffer[0] << 8) & 0xff00) + (buffer[1] & 0xFF);
|
y = ((buffer[2] << 8) & 0xff00) + (buffer[3] & 0xFF);
|
z = ((buffer[4] << 8) & 0xff00) + (buffer[5] & 0xFF);
|
|
axis.x = (pdata->orientation[0]) * x + (pdata->orientation[1]) * y + (pdata->orientation[2]) * z;
|
axis.y = (pdata->orientation[3]) * x + (pdata->orientation[4]) * y + (pdata->orientation[5]) * z;
|
axis.z = (pdata->orientation[6]) * x + (pdata->orientation[7]) * y + (pdata->orientation[8]) * z;
|
|
gsensor_report_value(client, &axis);
|
|
mutex_lock(&(sensor->data_mutex));
|
sensor->axis = axis;
|
mutex_unlock(&(sensor->data_mutex));
|
|
return ret;
|
}
|
|
static struct sensor_operate gsensor_iam20680_ops = {
|
.name = "iam20680_acc",
|
.type = SENSOR_TYPE_ACCEL,
|
.id_i2c = ACCEL_ID_IAM20680,
|
.read_reg = IAM20680_ACCEL_XOUT_H,
|
.read_len = 6,
|
.id_reg = IAM20680_WHOAMI,
|
.id_data = IAM20680_DEVICE_ID,
|
.precision = IAM20680_PRECISION,
|
.ctrl_reg = IAM20680_PWR_MGMT_2,
|
.int_status_reg = IAM20680_INT_STATUS,
|
.range = {-32768, 32768},
|
.trig = IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
|
.active = sensor_active,
|
.init = sensor_init,
|
.report = sensor_report_value,
|
};
|
|
/****************operate according to sensor chip:end************/
|
static int gsensor_iam20680_probe(struct i2c_client *client,
|
const struct i2c_device_id *devid)
|
{
|
return sensor_register_device(client, NULL, devid, &gsensor_iam20680_ops);
|
}
|
|
static int gsensor_iam20680_remove(struct i2c_client *client)
|
{
|
return sensor_unregister_device(client, NULL, &gsensor_iam20680_ops);
|
}
|
|
static const struct i2c_device_id gsensor_iam20680_id[] = {
|
{"iam20680_acc", ACCEL_ID_IAM20680},
|
{}
|
};
|
|
static struct i2c_driver gsensor_iam20680_driver = {
|
.probe = gsensor_iam20680_probe,
|
.remove = gsensor_iam20680_remove,
|
.shutdown = sensor_shutdown,
|
.id_table = gsensor_iam20680_id,
|
.driver = {
|
.name = "gsensor_iam20680",
|
#ifdef CONFIG_PM
|
.pm = &sensor_pm_ops,
|
#endif
|
},
|
};
|
|
module_i2c_driver(gsensor_iam20680_driver);
|
|
MODULE_AUTHOR("sxj <sxj@rock-chips.com>");
|
MODULE_DESCRIPTION("iam20680_acc 3-Axis accelerometer driver");
|
MODULE_LICENSE("GPL");
|
