* Broadcom cable/DSL/settop platforms
|
|
Required properties:
|
|
- compatible: "brcm,bcm3368", "brcm,bcm3384", "brcm,bcm33843"
|
"brcm,bcm3384-viper", "brcm,bcm33843-viper"
|
"brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6362", "brcm,bcm6368",
|
"brcm,bcm63168", "brcm,bcm63268",
|
"brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360",
|
"brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425"
|
|
The experimental -viper variants are for running Linux on the 3384's
|
BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor.
|
|
Power management
|
----------------
|
|
For power management (particularly, S2/S3/S5 system suspend), the following SoC
|
components are needed:
|
|
= Always-On control block (AON CTRL)
|
|
This hardware provides control registers for the "always-on" (even in low-power
|
modes) hardware, such as the Power Management State Machine (PMSM).
|
|
Required properties:
|
- compatible : should be one of
|
"brcm,bcm7425-aon-ctrl"
|
"brcm,bcm7429-aon-ctrl"
|
"brcm,bcm7435-aon-ctrl" and
|
"brcm,brcmstb-aon-ctrl"
|
- reg : the register start and length for the AON CTRL block
|
|
Example:
|
|
syscon@410000 {
|
compatible = "brcm,bcm7425-aon-ctrl", "brcm,brcmstb-aon-ctrl";
|
reg = <0x410000 0x400>;
|
};
|
|
= Memory controllers
|
|
A Broadcom STB SoC typically has a number of independent memory controllers,
|
each of which may have several associated hardware blocks, which are versioned
|
independently (control registers, DDR PHYs, etc.). One might consider
|
describing these controllers as a parent "memory controllers" block, which
|
contains N sub-nodes (one for each controller in the system), each of which is
|
associated with a number of hardware register resources (e.g., its PHY.
|
|
== MEMC (MEMory Controller)
|
|
Represents a single memory controller instance.
|
|
Required properties:
|
- compatible : should contain "brcm,brcmstb-memc" and "simple-bus"
|
- ranges : should contain the child address in the parent address
|
space, must be 0 here, and the register start and length of
|
the entire memory controller (including all sub nodes: DDR PHY,
|
arbiter, etc.)
|
- #address-cells : must be 1
|
- #size-cells : must be 1
|
|
Example:
|
|
memory-controller@0 {
|
compatible = "brcm,brcmstb-memc", "simple-bus";
|
ranges = <0x0 0x0 0xa000>;
|
#address-cells = <1>;
|
#size-cells = <1>;
|
|
memc-arb@1000 {
|
...
|
};
|
|
memc-ddr@2000 {
|
...
|
};
|
|
ddr-phy@6000 {
|
...
|
};
|
};
|
|
Should contain subnodes for any of the following relevant hardware resources:
|
|
== DDR PHY control
|
|
Control registers for this memory controller's DDR PHY.
|
|
Required properties:
|
- compatible : should contain one of these
|
"brcm,brcmstb-ddr-phy-v64.5"
|
"brcm,brcmstb-ddr-phy"
|
|
- reg : the DDR PHY register range and length
|
|
Example:
|
|
ddr-phy@6000 {
|
compatible = "brcm,brcmstb-ddr-phy-v64.5";
|
reg = <0x6000 0xc8>;
|
};
|
|
== DDR memory controller sequencer
|
|
Control registers for this memory controller's DDR memory sequencer
|
|
Required properties:
|
- compatible : should contain one of these
|
"brcm,bcm7425-memc-ddr"
|
"brcm,bcm7429-memc-ddr"
|
"brcm,bcm7435-memc-ddr" and
|
"brcm,brcmstb-memc-ddr"
|
|
- reg : the DDR sequencer register range and length
|
|
Example:
|
|
memc-ddr@2000 {
|
compatible = "brcm,bcm7425-memc-ddr", "brcm,brcmstb-memc-ddr";
|
reg = <0x2000 0x300>;
|
};
|
|
== MEMC Arbiter
|
|
The memory controller arbiter is responsible for memory clients allocation
|
(bandwidth, priorities etc.) and needs to have its contents restored during
|
deep sleep states (S3).
|
|
Required properties:
|
|
- compatible : should contain one of these
|
"brcm,brcmstb-memc-arb-v10.0.0.0"
|
"brcm,brcmstb-memc-arb"
|
|
- reg : the DDR Arbiter register range and length
|
|
Example:
|
|
memc-arb@1000 {
|
compatible = "brcm,brcmstb-memc-arb-v10.0.0.0";
|
reg = <0x1000 0x248>;
|
};
|
|
== Timers
|
|
The Broadcom STB chips contain a timer block with several general purpose
|
timers that can be used.
|
|
Required properties:
|
|
- compatible : should contain one of:
|
"brcm,bcm7425-timers"
|
"brcm,bcm7429-timers"
|
"brcm,bcm7435-timers" and
|
"brcm,brcmstb-timers"
|
- reg : the timers register range
|
- interrupts : the interrupt line for this timer block
|
|
Example:
|
|
timers: timer@4067c0 {
|
compatible = "brcm,bcm7425-timers", "brcm,brcmstb-timers";
|
reg = <0x4067c0 0x40>;
|
interrupts = <&periph_intc 19>;
|
};
|
