#
|
# QCOM Soc drivers
|
#
|
menu "Qualcomm SoC drivers"
|
|
config QCOM_COMMAND_DB
|
tristate "Qualcomm Command DB"
|
depends on ARCH_QCOM || COMPILE_TEST
|
depends on OF_RESERVED_MEM
|
help
|
Command DB queries shared memory by key string for shared system
|
resources. Platform drivers that require to set state of a shared
|
resource on a RPM-hardened platform must use this database to get
|
SoC specific identifier and information for the shared resources.
|
|
config QCOM_GENI_SE
|
tristate "QCOM GENI Serial Engine Driver"
|
depends on ARCH_QCOM || COMPILE_TEST
|
help
|
This driver is used to manage Generic Interface (GENI) firmware based
|
Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper. This
|
driver is also used to manage the common aspects of multiple Serial
|
Engines present in the QUP.
|
|
config QCOM_GLINK_SSR
|
tristate "Qualcomm Glink SSR driver"
|
depends on RPMSG
|
depends on QCOM_RPROC_COMMON
|
help
|
Say y here to enable GLINK SSR support. The GLINK SSR driver
|
implements the SSR protocol for notifying the remote processor about
|
neighboring subsystems going up or down.
|
|
config QCOM_GSBI
|
tristate "QCOM General Serial Bus Interface"
|
depends on ARCH_QCOM
|
select MFD_SYSCON
|
help
|
Say y here to enable GSBI support. The GSBI provides control
|
functions for connecting the underlying serial UART, SPI, and I2C
|
devices to the output pins.
|
|
config QCOM_LLCC
|
tristate "Qualcomm Technologies, Inc. LLCC driver"
|
depends on ARCH_QCOM
|
help
|
Qualcomm Technologies, Inc. platform specific
|
Last Level Cache Controller(LLCC) driver. This provides interfaces
|
to clients that use the LLCC. Say yes here to enable LLCC slice
|
driver.
|
|
config QCOM_SDM845_LLCC
|
tristate "Qualcomm Technologies, Inc. SDM845 LLCC driver"
|
depends on QCOM_LLCC
|
help
|
Say yes here to enable the LLCC driver for SDM845. This provides
|
data required to configure LLCC so that clients can start using the
|
LLCC slices.
|
|
config QCOM_MDT_LOADER
|
tristate
|
select QCOM_SCM
|
|
config QCOM_PM
|
bool "Qualcomm Power Management"
|
depends on ARCH_QCOM && !ARM64
|
select ARM_CPU_SUSPEND
|
select QCOM_SCM
|
help
|
QCOM Platform specific power driver to manage cores and L2 low power
|
modes. It interface with various system drivers to put the cores in
|
low power modes.
|
|
config QCOM_QMI_HELPERS
|
tristate
|
depends on ARCH_QCOM && NET
|
help
|
Helper library for handling QMI encoded messages. QMI encoded
|
messages are used in communication between the majority of QRTR
|
clients and this helpers provide the common functionality needed for
|
doing this from a kernel driver.
|
|
config QCOM_RMTFS_MEM
|
tristate "Qualcomm Remote Filesystem memory driver"
|
depends on ARCH_QCOM
|
select QCOM_SCM
|
help
|
The Qualcomm remote filesystem memory driver is used for allocating
|
and exposing regions of shared memory with remote processors for the
|
purpose of exchanging sector-data between the remote filesystem
|
service and its clients.
|
|
Say y here if you intend to boot the modem remoteproc.
|
|
config QCOM_RPMH
|
tristate "Qualcomm RPM-Hardened (RPMH) Communication"
|
depends on ARCH_QCOM && ARM64 && OF || COMPILE_TEST
|
help
|
Support for communication with the hardened-RPM blocks in
|
Qualcomm Technologies Inc (QTI) SoCs. RPMH communication uses an
|
internal bus to transmit state requests for shared resources. A set
|
of hardware components aggregate requests for these resources and
|
help apply the aggregated state on the resource.
|
|
config QCOM_SMEM
|
tristate "Qualcomm Shared Memory Manager (SMEM)"
|
depends on ARCH_QCOM
|
depends on HWSPINLOCK
|
help
|
Say y here to enable support for the Qualcomm Shared Memory Manager.
|
The driver provides an interface to items in a heap shared among all
|
processors in a Qualcomm platform.
|
|
config QCOM_SMD_RPM
|
tristate "Qualcomm Resource Power Manager (RPM) over SMD"
|
depends on ARCH_QCOM
|
depends on RPMSG && OF
|
help
|
If you say yes to this option, support will be included for the
|
Resource Power Manager system found in the Qualcomm 8974 based
|
devices.
|
|
This is required to access many regulators, clocks and bus
|
frequencies controlled by the RPM on these devices.
|
|
Say M here if you want to include support for the Qualcomm RPM as a
|
module. This will build a module called "qcom-smd-rpm".
|
|
config QCOM_SMEM_STATE
|
bool
|
|
config QCOM_SMP2P
|
tristate "Qualcomm Shared Memory Point to Point support"
|
depends on MAILBOX
|
depends on QCOM_SMEM
|
select QCOM_SMEM_STATE
|
help
|
Say yes here to support the Qualcomm Shared Memory Point to Point
|
protocol.
|
|
config QCOM_SMSM
|
tristate "Qualcomm Shared Memory State Machine"
|
depends on QCOM_SMEM
|
select QCOM_SMEM_STATE
|
help
|
Say yes here to support the Qualcomm Shared Memory State Machine.
|
The state machine is represented by bits in shared memory.
|
|
config QCOM_WCNSS_CTRL
|
tristate "Qualcomm WCNSS control driver"
|
depends on ARCH_QCOM
|
depends on RPMSG
|
help
|
Client driver for the WCNSS_CTRL SMD channel, used to download nv
|
firmware to a newly booted WCNSS chip.
|
|
config QCOM_APR
|
tristate "Qualcomm APR Bus (Asynchronous Packet Router)"
|
depends on ARCH_QCOM
|
depends on RPMSG
|
help
|
Enable APR IPC protocol support between
|
application processor and QDSP6. APR is
|
used by audio driver to configure QDSP6
|
ASM, ADM and AFE modules.
|
endmenu
|
