Analog Device ADV7511(W)/13/33 HDMI Encoders
|
-----------------------------------------
|
|
The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters
|
compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
|
S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while
|
the others support RGB interface.
|
|
Required properties:
|
|
- compatible: Should be one of:
|
"adi,adv7511"
|
"adi,adv7511w"
|
"adi,adv7513"
|
"adi,adv7533"
|
|
- reg: I2C slave addresses
|
The ADV7511 internal registers are split into four pages exposed through
|
different I2C addresses, creating four register maps. Each map has it own
|
I2C address and acts as a standard slave device on the I2C bus. The main
|
address is mandatory, others are optional and revert to defaults if not
|
specified.
|
|
|
The ADV7511 supports a large number of input data formats that differ by their
|
color depth, color format, clock mode, bit justification and random
|
arrangement of components on the data bus. The combination of the following
|
properties describe the input and map directly to the video input tables of the
|
ADV7511 datasheet that document all the supported combinations.
|
|
- adi,input-depth: Number of bits per color component at the input (8, 10 or
|
12).
|
- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
|
"yuv444".
|
- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
|
pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
|
data driven on both edges).
|
|
The following input format properties are required except in "rgb 1x" and
|
"yuv444 1x" modes, in which case they must not be specified.
|
|
- adi,input-style: The input components arrangement variant (1, 2 or 3), as
|
listed in the input format tables in the datasheet.
|
- adi,input-justification: The input bit justification ("left", "evenly",
|
"right").
|
|
- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
|
- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
|
- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
|
- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
|
on the chip.
|
- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
|
needed only for ADV7511.
|
|
The following properties are required for ADV7533:
|
|
- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
|
be one of 1, 2, 3 or 4.
|
- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
|
- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
|
- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
|
either 1.2V or 1.8V.
|
|
Optional properties:
|
|
- interrupts: Specifier for the ADV7511 interrupt
|
- pd-gpios: Specifier for the GPIO connected to the power down signal
|
|
- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
|
(-1200 ps .. 1600 ps). Defaults to no delay.
|
- adi,embedded-sync: The input uses synchronization signals embedded in the
|
data stream (similar to BT.656). Defaults to separate H/V synchronization
|
signals.
|
- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing
|
generator. The chip will rely on the sync signals in the DSI data lanes,
|
rather than generate its own timings for HDMI output.
|
- clocks: from common clock binding: reference to the CEC clock.
|
- clock-names: from common clock binding: must be "cec".
|
- reg-names : Names of maps with programmable addresses.
|
It can contain any map needing a non-default address.
|
Possible maps names are : "main", "edid", "cec", "packet"
|
|
Required nodes:
|
|
The ADV7511 has two video ports. Their connections are modelled using the OF
|
graph bindings specified in Documentation/devicetree/bindings/graph.txt.
|
|
- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the
|
remote endpoint phandle should be a reference to a valid mipi_dsi_host device
|
node.
|
- Video port 1 for the HDMI output
|
- Audio port 2 for the HDMI audio input
|
|
|
Example
|
-------
|
|
adv7511w: hdmi@39 {
|
compatible = "adi,adv7511w";
|
/*
|
* The EDID page will be accessible on address 0x66 on the I2C
|
* bus. All other maps continue to use their default addresses.
|
*/
|
reg = <0x39>, <0x66>;
|
reg-names = "main", "edid";
|
interrupt-parent = <&gpio3>;
|
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
|
clocks = <&cec_clock>;
|
clock-names = "cec";
|
|
adi,input-depth = <8>;
|
adi,input-colorspace = "rgb";
|
adi,input-clock = "1x";
|
adi,input-style = <1>;
|
adi,input-justification = "evenly";
|
|
ports {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
|
port@0 {
|
reg = <0>;
|
adv7511w_in: endpoint {
|
remote-endpoint = <&dpi_out>;
|
};
|
};
|
|
port@1 {
|
reg = <1>;
|
adv7511_out: endpoint {
|
remote-endpoint = <&hdmi_connector_in>;
|
};
|
};
|
|
port@2 {
|
reg = <2>;
|
codec_endpoint: endpoint {
|
remote-endpoint = <&i2s0_cpu_endpoint>;
|
};
|
};
|
};
|
};
|
