// SPDX-License-Identifier: GPL-2.0
|
#include "qcom-ipq8064.dtsi"
|
#include <dt-bindings/input/input.h>
|
|
/ {
|
model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
|
|
aliases {
|
serial0 = &gsbi4_serial;
|
};
|
|
chosen {
|
stdout-path = "serial0:115200n8";
|
};
|
|
soc {
|
gsbi@16300000 {
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
status = "ok";
|
|
serial@16340000 {
|
status = "ok";
|
};
|
};
|
|
gsbi5: gsbi@1a200000 {
|
qcom,mode = <GSBI_PROT_SPI>;
|
status = "ok";
|
|
spi4: spi@1a280000 {
|
status = "ok";
|
spi-max-frequency = <50000000>;
|
|
pinctrl-0 = <&spi_pins>;
|
pinctrl-names = "default";
|
|
cs-gpios = <&qcom_pinmux 20 0>;
|
|
flash: m25p80@0 {
|
compatible = "s25fl256s1";
|
#address-cells = <1>;
|
#size-cells = <1>;
|
spi-max-frequency = <50000000>;
|
reg = <0>;
|
|
partition@0 {
|
label = "rootfs";
|
reg = <0x0 0x1000000>;
|
};
|
|
partition@1 {
|
label = "scratch";
|
reg = <0x1000000 0x1000000>;
|
};
|
};
|
};
|
};
|
|
sata-phy@1b400000 {
|
status = "ok";
|
};
|
|
sata@29000000 {
|
ports-implemented = <0x1>;
|
status = "ok";
|
};
|
|
gpio_keys {
|
compatible = "gpio-keys";
|
pinctrl-0 = <&buttons_pins>;
|
pinctrl-names = "default";
|
|
button@1 {
|
label = "reset";
|
linux,code = <KEY_RESTART>;
|
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
linux,input-type = <1>;
|
debounce-interval = <60>;
|
};
|
button@2 {
|
label = "wps";
|
linux,code = <KEY_WPS_BUTTON>;
|
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
linux,input-type = <1>;
|
debounce-interval = <60>;
|
};
|
};
|
|
leds {
|
compatible = "gpio-leds";
|
pinctrl-0 = <&leds_pins>;
|
pinctrl-names = "default";
|
|
led@7 {
|
label = "led_usb1";
|
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
linux,default-trigger = "usbdev";
|
default-state = "off";
|
};
|
|
led@8 {
|
label = "led_usb3";
|
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
linux,default-trigger = "usbdev";
|
default-state = "off";
|
};
|
|
led@9 {
|
label = "status_led_fail";
|
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
default-state = "off";
|
};
|
|
led@26 {
|
label = "sata_led";
|
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
default-state = "off";
|
};
|
|
led@53 {
|
label = "status_led_pass";
|
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
default-state = "off";
|
};
|
};
|
};
|
};
|
