// SPDX-License-Identifier: GPL-2.0-or-later
|
// Copyright 2019 IBM Corp.
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
#include <dt-bindings/interrupt-controller/aspeed-scu-ic.h>
|
#include <dt-bindings/clock/ast2600-clock.h>
|
|
/ {
|
model = "Aspeed BMC";
|
compatible = "aspeed,ast2600";
|
#address-cells = <1>;
|
#size-cells = <1>;
|
interrupt-parent = <&gic>;
|
|
aliases {
|
i2c0 = &i2c0;
|
i2c1 = &i2c1;
|
i2c2 = &i2c2;
|
i2c3 = &i2c3;
|
i2c4 = &i2c4;
|
i2c5 = &i2c5;
|
i2c6 = &i2c6;
|
i2c7 = &i2c7;
|
i2c8 = &i2c8;
|
i2c9 = &i2c9;
|
i2c10 = &i2c10;
|
i2c11 = &i2c11;
|
i2c12 = &i2c12;
|
i2c13 = &i2c13;
|
i2c14 = &i2c14;
|
i2c15 = &i2c15;
|
serial0 = &uart1;
|
serial1 = &uart2;
|
serial2 = &uart3;
|
serial3 = &uart4;
|
serial4 = &uart5;
|
serial5 = &vuart1;
|
serial6 = &vuart2;
|
};
|
|
|
cpus {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
enable-method = "aspeed,ast2600-smp";
|
|
cpu@f00 {
|
compatible = "arm,cortex-a7";
|
device_type = "cpu";
|
reg = <0xf00>;
|
};
|
|
cpu@f01 {
|
compatible = "arm,cortex-a7";
|
device_type = "cpu";
|
reg = <0xf01>;
|
};
|
};
|
|
timer {
|
compatible = "arm,armv7-timer";
|
interrupt-parent = <&gic>;
|
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
|
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
|
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
|
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
|
clocks = <&syscon ASPEED_CLK_HPLL>;
|
arm,cpu-registers-not-fw-configured;
|
always-on;
|
};
|
|
ahb {
|
compatible = "simple-bus";
|
#address-cells = <1>;
|
#size-cells = <1>;
|
device_type = "soc";
|
ranges;
|
|
gic: interrupt-controller@40461000 {
|
compatible = "arm,cortex-a7-gic";
|
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
|
#interrupt-cells = <3>;
|
interrupt-controller;
|
interrupt-parent = <&gic>;
|
reg = <0x40461000 0x1000>,
|
<0x40462000 0x1000>,
|
<0x40464000 0x2000>,
|
<0x40466000 0x2000>;
|
};
|
|
fmc: spi@1e620000 {
|
reg = < 0x1e620000 0xc4
|
0x20000000 0x10000000 >;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
compatible = "aspeed,ast2600-fmc";
|
clocks = <&syscon ASPEED_CLK_AHB>;
|
status = "disabled";
|
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
|
flash@0 {
|
reg = < 0 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
flash@1 {
|
reg = < 1 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
flash@2 {
|
reg = < 2 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
};
|
|
spi1: spi@1e630000 {
|
reg = < 0x1e630000 0xc4
|
0x30000000 0x10000000 >;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
compatible = "aspeed,ast2600-spi";
|
clocks = <&syscon ASPEED_CLK_AHB>;
|
status = "disabled";
|
flash@0 {
|
reg = < 0 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
flash@1 {
|
reg = < 1 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
};
|
|
spi2: spi@1e631000 {
|
reg = < 0x1e631000 0xc4
|
0x50000000 0x10000000 >;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
compatible = "aspeed,ast2600-spi";
|
clocks = <&syscon ASPEED_CLK_AHB>;
|
status = "disabled";
|
flash@0 {
|
reg = < 0 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
flash@1 {
|
reg = < 1 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
flash@2 {
|
reg = < 2 >;
|
compatible = "jedec,spi-nor";
|
spi-max-frequency = <50000000>;
|
status = "disabled";
|
};
|
};
|
|
mdio0: mdio@1e650000 {
|
compatible = "aspeed,ast2600-mdio";
|
reg = <0x1e650000 0x8>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
status = "disabled";
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_mdio1_default>;
|
};
|
|
mdio1: mdio@1e650008 {
|
compatible = "aspeed,ast2600-mdio";
|
reg = <0x1e650008 0x8>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
status = "disabled";
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_mdio2_default>;
|
};
|
|
mdio2: mdio@1e650010 {
|
compatible = "aspeed,ast2600-mdio";
|
reg = <0x1e650010 0x8>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
status = "disabled";
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_mdio3_default>;
|
};
|
|
mdio3: mdio@1e650018 {
|
compatible = "aspeed,ast2600-mdio";
|
reg = <0x1e650018 0x8>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
status = "disabled";
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_mdio4_default>;
|
};
|
|
mac0: ftgmac@1e660000 {
|
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
|
reg = <0x1e660000 0x180>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>;
|
status = "disabled";
|
};
|
|
mac1: ftgmac@1e680000 {
|
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
|
reg = <0x1e680000 0x180>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>;
|
status = "disabled";
|
};
|
|
mac2: ftgmac@1e670000 {
|
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
|
reg = <0x1e670000 0x180>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>;
|
status = "disabled";
|
};
|
|
mac3: ftgmac@1e690000 {
|
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
|
reg = <0x1e690000 0x180>;
|
#address-cells = <1>;
|
#size-cells = <0>;
|
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>;
|
status = "disabled";
|
};
|
|
ehci0: usb@1e6a1000 {
|
compatible = "aspeed,ast2600-ehci", "generic-ehci";
|
reg = <0x1e6a1000 0x100>;
|
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_usb2ah_default>;
|
status = "disabled";
|
};
|
|
ehci1: usb@1e6a3000 {
|
compatible = "aspeed,ast2600-ehci", "generic-ehci";
|
reg = <0x1e6a3000 0x100>;
|
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_usb2bh_default>;
|
status = "disabled";
|
};
|
|
uhci: usb@1e6b0000 {
|
compatible = "aspeed,ast2600-uhci", "generic-uhci";
|
reg = <0x1e6b0000 0x100>;
|
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
|
#ports = <2>;
|
clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
|
status = "disabled";
|
/*
|
* No default pinmux, it will follow EHCI, use an
|
* explicit pinmux override if EHCI is not enabled.
|
*/
|
};
|
|
vhub: usb-vhub@1e6a0000 {
|
compatible = "aspeed,ast2600-usb-vhub";
|
reg = <0x1e6a0000 0x350>;
|
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
|
aspeed,vhub-downstream-ports = <7>;
|
aspeed,vhub-generic-endpoints = <21>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_usb2ad_default>;
|
status = "disabled";
|
};
|
|
apb {
|
compatible = "simple-bus";
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges;
|
|
syscon: syscon@1e6e2000 {
|
compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd";
|
reg = <0x1e6e2000 0x1000>;
|
ranges = <0 0x1e6e2000 0x1000>;
|
#address-cells = <1>;
|
#size-cells = <1>;
|
#clock-cells = <1>;
|
#reset-cells = <1>;
|
|
pinctrl: pinctrl {
|
compatible = "aspeed,ast2600-pinctrl";
|
};
|
|
smp-memram@180 {
|
compatible = "aspeed,ast2600-smpmem";
|
reg = <0x180 0x40>;
|
};
|
|
scu_ic0: interrupt-controller@560 {
|
#interrupt-cells = <1>;
|
compatible = "aspeed,ast2600-scu-ic0";
|
reg = <0x560 0x4>;
|
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
|
interrupt-controller;
|
};
|
|
scu_ic1: interrupt-controller@570 {
|
#interrupt-cells = <1>;
|
compatible = "aspeed,ast2600-scu-ic1";
|
reg = <0x570 0x4>;
|
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
|
interrupt-controller;
|
};
|
};
|
|
rng: hwrng@1e6e2524 {
|
compatible = "timeriomem_rng";
|
reg = <0x1e6e2524 0x4>;
|
period = <1>;
|
quality = <100>;
|
};
|
|
xdma: xdma@1e6e7000 {
|
compatible = "aspeed,ast2600-xdma";
|
reg = <0x1e6e7000 0x100>;
|
clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
|
resets = <&syscon ASPEED_RESET_DEV_XDMA>, <&syscon ASPEED_RESET_RC_XDMA>;
|
reset-names = "device", "root-complex";
|
interrupts-extended = <&gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
|
<&scu_ic0 ASPEED_AST2600_SCU_IC0_PCIE_PERST_LO_TO_HI>;
|
aspeed,pcie-device = "bmc";
|
aspeed,scu = <&syscon>;
|
status = "disabled";
|
};
|
|
gpio0: gpio@1e780000 {
|
#gpio-cells = <2>;
|
gpio-controller;
|
compatible = "aspeed,ast2600-gpio";
|
reg = <0x1e780000 0x400>;
|
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
|
gpio-ranges = <&pinctrl 0 0 208>;
|
ngpios = <208>;
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
interrupt-controller;
|
#interrupt-cells = <2>;
|
};
|
|
gpio1: gpio@1e780800 {
|
#gpio-cells = <2>;
|
gpio-controller;
|
compatible = "aspeed,ast2600-gpio";
|
reg = <0x1e780800 0x800>;
|
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
|
gpio-ranges = <&pinctrl 0 208 36>;
|
ngpios = <36>;
|
clocks = <&syscon ASPEED_CLK_APB1>;
|
interrupt-controller;
|
#interrupt-cells = <2>;
|
};
|
|
rtc: rtc@1e781000 {
|
compatible = "aspeed,ast2600-rtc";
|
reg = <0x1e781000 0x18>;
|
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
|
status = "disabled";
|
};
|
|
timer: timer@1e782000 {
|
compatible = "aspeed,ast2600-timer";
|
reg = <0x1e782000 0x90>;
|
interrupts-extended = <&gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
|
<&gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_APB1>;
|
clock-names = "PCLK";
|
status = "disabled";
|
};
|
|
uart1: serial@1e783000 {
|
compatible = "ns16550a";
|
reg = <0x1e783000 0x20>;
|
reg-shift = <2>;
|
reg-io-width = <4>;
|
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>;
|
resets = <&lpc_reset 4>;
|
no-loopback-test;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>;
|
status = "disabled";
|
};
|
|
uart5: serial@1e784000 {
|
compatible = "ns16550a";
|
reg = <0x1e784000 0x1000>;
|
reg-shift = <2>;
|
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_UART5CLK>;
|
no-loopback-test;
|
};
|
|
wdt1: watchdog@1e785000 {
|
compatible = "aspeed,ast2600-wdt";
|
reg = <0x1e785000 0x40>;
|
};
|
|
wdt2: watchdog@1e785040 {
|
compatible = "aspeed,ast2600-wdt";
|
reg = <0x1e785040 0x40>;
|
status = "disabled";
|
};
|
|
wdt3: watchdog@1e785080 {
|
compatible = "aspeed,ast2600-wdt";
|
reg = <0x1e785080 0x40>;
|
status = "disabled";
|
};
|
|
wdt4: watchdog@1e7850c0 {
|
compatible = "aspeed,ast2600-wdt";
|
reg = <0x1e7850C0 0x40>;
|
status = "disabled";
|
};
|
|
lpc: lpc@1e789000 {
|
compatible = "aspeed,ast2600-lpc", "simple-mfd";
|
reg = <0x1e789000 0x1000>;
|
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0x0 0x1e789000 0x1000>;
|
|
lpc_bmc: lpc-bmc@0 {
|
compatible = "aspeed,ast2600-lpc-bmc", "simple-mfd", "syscon";
|
reg = <0x0 0x80>;
|
reg-io-width = <4>;
|
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0x0 0x0 0x80>;
|
|
kcs1: kcs@24 {
|
compatible = "aspeed,ast2500-kcs-bmc-v2";
|
reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
|
interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
|
kcs_chan = <1>;
|
status = "disabled";
|
};
|
kcs2: kcs@28 {
|
compatible = "aspeed,ast2500-kcs-bmc-v2";
|
reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
|
interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
|
status = "disabled";
|
};
|
kcs3: kcs@2c {
|
compatible = "aspeed,ast2500-kcs-bmc-v2";
|
reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
|
interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
|
status = "disabled";
|
};
|
};
|
|
lpc_host: lpc-host@80 {
|
compatible = "aspeed,ast2600-lpc-host", "simple-mfd", "syscon";
|
reg = <0x80 0x1e0>;
|
reg-io-width = <4>;
|
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0x0 0x80 0x1e0>;
|
|
kcs4: kcs@94 {
|
compatible = "aspeed,ast2500-kcs-bmc-v2";
|
reg = <0x94 0x1>, <0x98 0x1>, <0x9c 0x1>;
|
interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
|
status = "disabled";
|
};
|
|
lpc_ctrl: lpc-ctrl@0 {
|
compatible = "aspeed,ast2600-lpc-ctrl";
|
reg = <0x0 0x80>;
|
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
|
status = "disabled";
|
};
|
|
lpc_snoop: lpc-snoop@0 {
|
compatible = "aspeed,ast2600-lpc-snoop";
|
reg = <0x0 0x80>;
|
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
|
status = "disabled";
|
};
|
|
lhc: lhc@20 {
|
compatible = "aspeed,ast2600-lhc";
|
reg = <0x20 0x24 0x48 0x8>;
|
};
|
|
lpc_reset: reset-controller@18 {
|
compatible = "aspeed,ast2600-lpc-reset";
|
reg = <0x18 0x4>;
|
#reset-cells = <1>;
|
};
|
|
ibt: ibt@c0 {
|
compatible = "aspeed,ast2600-ibt-bmc";
|
reg = <0xc0 0x18>;
|
interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
|
status = "disabled";
|
};
|
};
|
};
|
|
sdc: sdc@1e740000 {
|
compatible = "aspeed,ast2600-sd-controller";
|
reg = <0x1e740000 0x100>;
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0 0x1e740000 0x10000>;
|
clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
|
status = "disabled";
|
|
sdhci0: sdhci@1e740100 {
|
compatible = "aspeed,ast2600-sdhci", "sdhci";
|
reg = <0x100 0x100>;
|
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
|
sdhci,auto-cmd12;
|
clocks = <&syscon ASPEED_CLK_SDIO>;
|
status = "disabled";
|
};
|
|
sdhci1: sdhci@1e740200 {
|
compatible = "aspeed,ast2600-sdhci", "sdhci";
|
reg = <0x200 0x100>;
|
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
|
sdhci,auto-cmd12;
|
clocks = <&syscon ASPEED_CLK_SDIO>;
|
status = "disabled";
|
};
|
};
|
|
emmc_controller: sdc@1e750000 {
|
compatible = "aspeed,ast2600-sd-controller";
|
reg = <0x1e750000 0x100>;
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0 0x1e750000 0x10000>;
|
clocks = <&syscon ASPEED_CLK_GATE_EMMCCLK>;
|
status = "disabled";
|
|
emmc: sdhci@1e750100 {
|
compatible = "aspeed,ast2600-sdhci";
|
reg = <0x100 0x100>;
|
sdhci,auto-cmd12;
|
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_EMMC>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_emmc_default>;
|
};
|
};
|
|
vuart1: serial@1e787000 {
|
compatible = "aspeed,ast2500-vuart";
|
reg = <0x1e787000 0x40>;
|
reg-shift = <2>;
|
interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_APB1>;
|
no-loopback-test;
|
status = "disabled";
|
};
|
|
vuart2: serial@1e788000 {
|
compatible = "aspeed,ast2500-vuart";
|
reg = <0x1e788000 0x40>;
|
reg-shift = <2>;
|
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_APB1>;
|
no-loopback-test;
|
status = "disabled";
|
};
|
|
uart2: serial@1e78d000 {
|
compatible = "ns16550a";
|
reg = <0x1e78d000 0x20>;
|
reg-shift = <2>;
|
reg-io-width = <4>;
|
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>;
|
resets = <&lpc_reset 5>;
|
no-loopback-test;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>;
|
status = "disabled";
|
};
|
|
uart3: serial@1e78e000 {
|
compatible = "ns16550a";
|
reg = <0x1e78e000 0x20>;
|
reg-shift = <2>;
|
reg-io-width = <4>;
|
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>;
|
resets = <&lpc_reset 6>;
|
no-loopback-test;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>;
|
status = "disabled";
|
};
|
|
uart4: serial@1e78f000 {
|
compatible = "ns16550a";
|
reg = <0x1e78f000 0x20>;
|
reg-shift = <2>;
|
reg-io-width = <4>;
|
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
|
clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>;
|
resets = <&lpc_reset 7>;
|
no-loopback-test;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_txd4_default &pinctrl_rxd4_default>;
|
status = "disabled";
|
};
|
|
i2c: bus@1e78a000 {
|
compatible = "simple-bus";
|
#address-cells = <1>;
|
#size-cells = <1>;
|
ranges = <0 0x1e78a000 0x1000>;
|
};
|
|
fsim0: fsi@1e79b000 {
|
compatible = "aspeed,ast2600-fsi-master", "fsi-master";
|
reg = <0x1e79b000 0x94>;
|
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_fsi1_default>;
|
clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
|
status = "disabled";
|
};
|
|
fsim1: fsi@1e79b100 {
|
compatible = "aspeed,ast2600-fsi-master", "fsi-master";
|
reg = <0x1e79b100 0x94>;
|
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_fsi2_default>;
|
clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
|
status = "disabled";
|
};
|
};
|
};
|
};
|
|
#include "aspeed-g6-pinctrl.dtsi"
|
|
&i2c {
|
i2c0: i2c-bus@80 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x80 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c1_default>;
|
status = "disabled";
|
};
|
|
i2c1: i2c-bus@100 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x100 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c2_default>;
|
status = "disabled";
|
};
|
|
i2c2: i2c-bus@180 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x180 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c3_default>;
|
status = "disabled";
|
};
|
|
i2c3: i2c-bus@200 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x200 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c4_default>;
|
status = "disabled";
|
};
|
|
i2c4: i2c-bus@280 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x280 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c5_default>;
|
status = "disabled";
|
};
|
|
i2c5: i2c-bus@300 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x300 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c6_default>;
|
status = "disabled";
|
};
|
|
i2c6: i2c-bus@380 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x380 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c7_default>;
|
status = "disabled";
|
};
|
|
i2c7: i2c-bus@400 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x400 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c8_default>;
|
status = "disabled";
|
};
|
|
i2c8: i2c-bus@480 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x480 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c9_default>;
|
status = "disabled";
|
};
|
|
i2c9: i2c-bus@500 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x500 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c10_default>;
|
status = "disabled";
|
};
|
|
i2c10: i2c-bus@580 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x580 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c11_default>;
|
status = "disabled";
|
};
|
|
i2c11: i2c-bus@600 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x600 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c12_default>;
|
status = "disabled";
|
};
|
|
i2c12: i2c-bus@680 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x680 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c13_default>;
|
status = "disabled";
|
};
|
|
i2c13: i2c-bus@700 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x700 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c14_default>;
|
status = "disabled";
|
};
|
|
i2c14: i2c-bus@780 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x780 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c15_default>;
|
status = "disabled";
|
};
|
|
i2c15: i2c-bus@800 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
#interrupt-cells = <1>;
|
reg = <0x800 0x80>;
|
compatible = "aspeed,ast2600-i2c-bus";
|
clocks = <&syscon ASPEED_CLK_APB2>;
|
resets = <&syscon ASPEED_RESET_I2C>;
|
interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
|
bus-frequency = <100000>;
|
pinctrl-names = "default";
|
pinctrl-0 = <&pinctrl_i2c16_default>;
|
status = "disabled";
|
};
|
};
|
